BILLET ALUMINUM MOTOR MOUNTS FOR 911
THESE MOUNTS HELP YOU GET THE RIGIDITY YOU NEED. FOR TRACK AND STREET.
$80.00/SET OF TWO
THESE MOUNTS HELP YOU GET THE RIGIDITY YOU NEED. FOR TRACK AND STREET.
$80.00/SET OF TWO
MECHANICAL CHAIN TENSIONERS
FOR 911USE THESE MECHANICAL TENSIONERS TO SET CAM TIMING
$60.00/Set OF TWO
FOR 911USE THESE MECHANICAL TENSIONERS TO SET CAM TIMING
$60.00/Set OF TWO
SPROCKET ALIGNMENT TOOL FOR 911
GET THE RIGHT SETTING EVERY TIME NO MORE GUESSING FOR SPROCKET
ALIGNMENT.
$95
GET THE RIGHT SETTING EVERY TIME NO MORE GUESSING FOR SPROCKET
ALIGNMENT.
$95
Aluminum Crank pulley trigger kit
Aluminum pulley, distributor plug, sensor mount with 36-1 trigger wheel.
$260 With A/C
$260 with-out A/C
( race )
Aluminum pulley, distributor plug, sensor mount with 36-1 trigger wheel.
$260 With A/C
$260 with-out A/C
( race )
Aluminum Crank pulley trigger kit
Aluminum pulley, distributor plug, sensor mount with 60-2 trigger wheel.
$260 With A/C
$260 with-out A/C
( race )
Aluminum pulley, distributor plug, sensor mount with 60-2 trigger wheel.
$260 With A/C
$260 with-out A/C
( race )
3.6 L 911 engine Power Steering Camshaft Block Off.
$50 Red
$50 Black
$50 Gold
$50 Red
$50 Black
$50 Gold
3.6 L 911 engine Power Steering Camshaft Block Off with cam sensor mount. Sequential
Application.
$60 Aluminum block
$80 CAM sensor
Application.
$60 Aluminum block
$80 CAM sensor
Porsche 993 header with heat
These headers inluded in this exhaust have Gillet flanges which means that you must have the
same type flange on your headers its the 3-Bolt Round, if you have the oval flange Bischoff
these headers will not work, Gillet are most commonly used on 96-98 993's. Brand New Stainless
Steel Porsche 993 Non-Turbo headers with heatbox, these are direct bolt ons no mods
necessary, made for 993 N/A
1 5/8" Piping for header piping going to the heads, racing merge collector, 2 1/4" pipe after
heatbox going to cats
$900
These headers inluded in this exhaust have Gillet flanges which means that you must have the
same type flange on your headers its the 3-Bolt Round, if you have the oval flange Bischoff
these headers will not work, Gillet are most commonly used on 96-98 993's. Brand New Stainless
Steel Porsche 993 Non-Turbo headers with heatbox, these are direct bolt ons no mods
necessary, made for 993 N/A
1 5/8" Piping for header piping going to the heads, racing merge collector, 2 1/4" pipe after
heatbox going to cats
$900
Porsche 993 muffler tip
For 95- 98 Porsche 993 Narrow body only, made of T 304 Stainless steel. Oval 4.5 x 3 inches
angle cut. Tig welds, rolled edges.
$120 set.
For 95- 98 Porsche 993 Narrow body only, made of T 304 Stainless steel. Oval 4.5 x 3 inches
angle cut. Tig welds, rolled edges.
$120 set.
Porsche 964 high flow header with muffler kit.
Mandrel bent tubing with fully mirror polished 304 stainless steel.
Gain 12 % horsepower with muffler kit.
$1200
Mandrel bent tubing with fully mirror polished 304 stainless steel.
Gain 12 % horsepower with muffler kit.
$1200
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
Aluminum Crank pulley trigger kit with sensor.
Sensor is from 2004 Ford Focus ZX5 ZX3 2.0L motor.
MOTORCRAFT Part # DY913 {#F5RZ6C315AA}
DOHC; 948F-6C315AA
sensor $30 with pulley kit $300 shipped
Sensor is from 2004 Ford Focus ZX5 ZX3 2.0L motor.
MOTORCRAFT Part # DY913 {#F5RZ6C315AA}
DOHC; 948F-6C315AA
sensor $30 with pulley kit $300 shipped
Porsche header installation tools
8 mm 5 1/2 inch or longer hex wrench Lower box end wrench does not work
13 mm deep offset box end wrench 6 mm not deep enough.
Both tool $30
8 mm 5 1/2 inch or longer hex wrench Lower box end wrench does not work
13 mm deep offset box end wrench 6 mm not deep enough.
Both tool $30
